Joined in 2023 
82 
63 About this deal
The Shotgun Combo Gauge is a 24″ vernier caliper slotted at one end to hold a sliding Drop Meter. It can be used alone or with our 23″ EXTENSION which bolts on to the Combo Gauge to make the overall drop/pitch length 48″. The Extension also has a neodymium magnet installed which essentially “glues” the whole Combo Gauge to the gun’s rib for hands-free operation, further enhancing its convenience and usability. The XS Sight Systems Magazine Tube Detent Swage is a tool that allows for the easy removal of magazine tube detents in Remington shotguns without creating holes or damaging the tube. MEASURING CHOKES — The BoreMaster as the “De-Liar.” The results obtained by measuring your fixed or screw-in chokes will surprise you. What one manufacturer calls Mod is another’s I.C. Buy screw-in chokes (12 ga) designated for steel shot and I.C. may be 0.003″ Modified around 0.010″ and Full AT 0.018″. These are readings from a Perazzi Mirage with Briley thin wall chokes for steel shot. Those of you with Polychokes can now accurately find the TRUE choke constriction for each designation on the Polychoke. These numbers will both surprise and enlighten you and add to the usefulness of this great product.
Shotgun Tools on 52 Products | Brownells
The Briley 20 GA. Tube Wrench is a universal wrench that fits all factory choked shotguns and Briley X-2 tubes, except for Briley special thinwall tubes. For best results, any existing choke should be removed with the Angle Blade Expanding Choke Reamer prior to using the Manson Precision 20 Gauge Reamer. The tap and reamer set can thread barrels to accept original equipment and aftermarket replacement tubes from Win-Choke, Browning Invector®, Mossberg Accu-Choke®, Weatherby, and Colonial Arms. The Magazine Tube Detent Swage is manufactured by XS Sight Systems and falls under the category of Straighteners & Dent Raisers. Fits all Winchester Model 12 s in 12, 16 and 20 gauge, including the Browning Reproduction in 20 gauge. Made with a plastic knob, aluminum fingers and handle, and stainless steel body, this choke tube wrench is available in both 12 gauge and 20 gauge.
The NYLON/BRASS DRIFT PUNCH is a combination punch designed for gunsmiths, machinists, and toolmakers. It has a hi-impact steel handle with a knurled grip for easy holding and accurate control. Shotgun bore diameters are all over the place, varying as much as 2% of nominal diameter. An example of this is an underbored Perazzi 28 gauge measuring .537/.538 (nominal is .550), a Browning Double Auto made around 1957 at .720 and a 1964 Browning Superposed 20 gauge at 0.625 (overbored). The question is how does one confirm that the BoreMaster is reading accurately? The method we use to verify the bore measurement is by measuring the CHAMBER dimensions. The chambers are typically held to a very tight spec which we measure to the thousands. Chamber dimensions are provided with the BoreMaster Instructions. Simplify the process of changing mainsprings in double barrel shotguns with the BROWNELLS SHOTGUN MAINSPRING TOOL. The notched blade tip captures the plunger head, compresses the spring, and lifts both parts free from the receiver.
FULL SEND by NELK
Universal Shotguns with 12 Gauge, 20 Gauge, .410 Bore, and 28 Gauge can use this bore gauge set. The direct-reading dial indicator mounted on a 16½" long shaft shows dents, bends, and other imperfections. The set is an excellent choice for professionals who require high accuracy in their work. The Pachmayr Recoil Pad Grinding Template is a useful tool for professional gunsmiths and DIY enthusiasts who want to customize their recoil pads without damaging the steel reinforcement plates. CHAMBER — Chamber dimensions — Chamber length — Forcing cone dimensions and rifle chambers with diameter dimensions of .400″ and up. To make the shopping experience with Brownells better, we have a number of representatives in Europe.The Dent Raiser is simple and easy to operate, and it does not require outside hammering or peening, which means there are no hammer marks to polish out and no need to reblue the barrel. Brass templates are available to prevent cutting into steel reinforcement plates while shaping a recoil pad. The templates work with all closed-side Pachmayr recoil pads.
Gunsmithing Tools - Everything You Need For Builds - Wheeler Gunsmithing Tools - Everything You Need For Builds - Wheeler
Multiple screw holes in the mounting plates provide compatibility with almost all types of hardware and recoil pads. The fixture is made of anodized aluminum with a matte red finish and measures 4" (10.2cm) long, 1½" (3.8cm) wide, 1-13⁄16" (4.6cm) high. The tap and reamer are made from high-speed steel and use the same interchangeable pilot bushings, which are available in diameter increments of .001" and are 2" long for accurate bore alignment. The Remington shotgun punch tip is .165" diameter Nylon tip without a steel pin, which is non-marring and used for removing trigger plate pins from 870, 1100, and 1187. The punch is supplied in Basic Set, 4-Way Set, and 6-Way Set configurations. Machined and hardened tips provide excellent grip and prevent damage to rusted or stubborn end caps.The Professional Shotgun Bore Micrometer Set by 100 Straight Products is a complete dial bore micrometer set that accurately measures bore diameter, choke constriction, chamber (except 10 gauge chambers), and forcing cone dimensions. The kit includes two punches, each 3-½" long, with a hole in the face of the #1 tool to fasten the ejector housing to the receiver with the lower portion of the rivet. The #2 tool secures the ejector spring within the ejector housing with the upper portion of the rivet. The Dent Raiser is 22-3/8" (56.8cm) long, has a 1" (2.5cm) dia. hardwood handle, and is suitable for Universal Shotguns. Detailed operating and maintenance instructions are included. The gauge is made of stainless steel with a bright polish and is 5-1/8" (13cm) long, making it a durable and reliable choice for those in need of a fast, visual verification of choke constriction.
Roblox Gear ID codes in October 2023 - Gamer Tweak
Before the detent style magazine spring & mag cap retention system, installing a magazine tube extension on Remington shotguns was a simple process that involved swapping out springs and screwing on the extension. The Remington/Mossberg Forend Wrench by Brownells is a durable tool that is adapted from the Remington factory design. It comes with a pilot that keeps the teeth square to the forend nut, which virtually eliminates damage to the wrench, forend, or forend nut. The Manson Precision 20 Gauge Reamer is a choke tube tool designed to provide superior results when used on a lathe. It is made by Manson Precision, a manufacturer of high-quality firearms tools and accessories. The product specs for the 20 gauge reamer are 11⁄16"-32 tpi, and it is categorized as a choke tube tool. RIFLE BARREL CHAMBERS can be accurately measured. Calibers with case diameters over .400″ – that includes the 30/30 and 30-06 variations — and metrics like the 8 mm and 7 mm Mauser and larger can be measured. Obviously the barrels have to be removed from bolt or lever guns, but single shots and any break guns are readily measurable. This is an extremely fast and accurate method of verifying a gun’s chamber – especially unusual metric, Continental, British or obsolete American barrels. It also verifies if a chamber has been altered to a wildcat configuration.The 20-gauge version of the wrench is 7-7/8" (20cm) long overall, with a 5" (12.7cm) long handle. The replacement sleeve is sold separately for 12 gauge only. This product falls under the Forend Wrenches category. The tool is made of hardened steel shank and plastic handle, providing maximum control and leverage. It eliminates the frustration of scratching and gouging the plunger or inner receiver surfaces with an ordinary screwdriver. The Deluxe Kit also includes an ejector spring rivet cutter that lets you take off just the peened area of the front rivet and often lets you re-peen the existing rivet. The punches are made of hardened steel with a blue finish, while the rivet cutter has a steel shaft and hardened steel cutter.
Great Deal 
New Comment