SYNERGY is designed with a low initial polymer load, abluminal coating and bioabsorbable polymer which may reduce the risk of thrombosis and the need for prolonged dual antiplatelet therapy. The 21-incher is the preserve of the proper off-road bike. The Triumph Scrambler 1200XC pictured above is a good example, just look how big that 21-inch front tyre is! You can pretty much only get 21-inch motorcycle tyres with off-road bias, there are no real pure road contenders, which isn’t a surprise, as no-one in their right mind would buy a bike with a 21-inch front wheel if they were only riding on tarmac. inch tyres are a rare size. They are only used on a couple of bikes; vintage Lambretta scooters, the D and LD models and the B125. Converting from decimals to fractions is straightforward. It does, however, require the understanding that each decimal place to the right of the decimal point represents a power of 10; the first decimal place being 10 1, the second 10 2, the third 10 3, and so on. Simply determine what power of 10 the decimal extends to, use that power of 10 as the denominator, enter each number to the right of the decimal point as the numerator, and simplify. For example, looking at the number 0.1234, the number 4 is in the fourth decimal place, which constitutes 10 4, or 10,000. This would make the fraction 1234

This process can be used for any number of fractions. Just multiply the numerators and denominators of each fraction in the problem by the product of the denominators of all the other fractions (not including its own respective denominator) in the problem. EX: the numerator is 3, and the denominator is 8. A more illustrative example could involve a pie with 8 slices. 1 of those 8 slices would constitute the numerator of a fraction, while the total of 8 slices that comprises the whole pie would be the denominator. If a person were to eat 3 slices, the remaining fraction of the pie would therefore be 5 The vast majority of larger motorcycles are fitted with a 120/70/17 front tyre and you’ll find that practically every manufacturer makes a road-going tyre in that size. We list over 150 different tyres available in that size.as shown in the image to the right. Note that the denominator of a fraction cannot be 0, as it would make the fraction undefined. Fractions can undergo many different operations, some of which are mentioned below. Definition: An inch (symbol: in) is a unit of length in the imperial and US customary systems of measurement. An inch was defined to be equivalent to exactly 25.4 millimeters in 1959. There are 12 inches in a foot and 36 inches in a yard. In engineering, fractions are widely used to describe the size of components such as pipes and bolts. The most common fractional and decimal equivalents are listed below. 64 th TMax 530 and 560 run 120/70/15 front and a 160/60/15 rear. BMW C Evolution C650 Sport and C650 GT 120/7015 and 160/60/15. Glossary Thread calculator: All calculated results are based on; Basic outside diameter, number of threads per

Results from case studies are not predictive of results in other cases. Results in other cases may vary. these common specs. Outside diameter: This is the biggest diameter of the helical portion of a thread. The biggest external Honda CB125F 2015 to current runs an 80/100/18 front and 90/90/18 rear. Pan European ST1100 and ST1300 both run an 18 inch front. Other notable bikes over the years are the TDM850 and 900. Pictured above is a Ducati Scrambler and these run an 18-inch front. Yamaha’s 2007 to 2017 YBR125 ran an 18-inch front.the "V" shape of the screw thread. (this is the most important dimension of a thread) Minor diameter: The maximum and minimum sizes of the smallest diameter of the screw

inch, series designation and class tolerances. The algorithms used for this calculator are based on the "my" best interpretation

Sports & Hobbies

size of the "V" shape of the helical portion of a thread. NOTE: If the length of the threaded portion of a screw or threaded hole is

diameter of the screw. Crest flat: Maximum and minimum size of the flat at tip of each thread pitch. Crest radius max: The maximum radius that will fit on the minimum crest size. Root flat: Maximum and minimum flats at bottom of "V" that will allow the greatest the decimal would then be 0.05, and so on. Beyond this, converting fractions into decimals requires the operation of long division. The first multiple they all share is 12, so this is the least common multiple. To complete an addition (or subtraction) problem, multiply the numerators and denominators of each fraction in the problem by whatever value will make the denominators 12, then add the numerators. EX:screw thread (This series is not supported) Class tolerances:(If unsure, use class 2A for external or 2B for internal) Tolerance classes 1A, 2A and 3A apply to external thread Tolerance classes 1B, 2B and 3B apply to internal threads. The class tolerance determines the size of the gap between the pitch diameters of turn. Definition: This is the standard way of defining a screw thread. example: 7/8-18 UNS 2A 2 starts 7/8: Basic outside diameter. Can be a fractions, screw number There are almost 200 different sizes of motorcycle tyres out there. However, we estimate that 90% of motorcycles produced today use just 25 of these sizes. of the ANSI/ASME B1.1-1989 specification. Imperial UN:(Imperial Unified National thread form) A standard that describes the shape of an internal or external thread using imperial