Kreg Straight Edge Guide XL-8 Ft

Product Information

When you’re cutting plywood or other sheets, making a straight cut is even more challenging because the cuts are so much longer. So, you need something that will guide the saw over 4′ to make a crosscut across the sheet, or 8′ to make a rip cut along the sheet’s length. Then, press the trigger and push forward ever so slowly. Make sure you keep the saw firmly against your guide until the end of the cut. And speaking of the end, don’t forget to cut until the end of your guide. Bump up the safety factor even further by wearing snug-fitting work gloves. They should offer enough protection that you don’t need to worry about accidentally being cut or burnt while operating the saw. After marking, use a deep pencil to draw straight lines on the board. Remember, drawing the lines straight will ensure that the cuts you make will be straight cuts. To make straight cuts with a circular saw perfectly, make the line as visible as you can by running the pencil several times. Step 5

In the case of making use of a circular saw, maintaining a cut line for cutting straight is impossible with a cutting guide. Even if you want to cut plywood, the vibration from the circular saw is enough to deviate you from going on straight lines and getting fine rip cuts with a circular saw blade. Most straight-edge clamps feature rubber feet for gripping the material. These rubber feet help prevent damages to the material. Moreover, the clamping mechanism works well in resisting the pressure that the straight edge receives from the saw. Swivel Heads

Finding Your Next Circular Saw Guide: A Buyer’s Guide

In this article, I am going to go over several advantages of using a guide rail, as well as explain the two different models of guide rail that you can use. Best Guide Rails for Circular Saw I would advise caution when building your own rip fence, make sure you follow whatever guide you are using to the letter. It is very possible that you will make a single mistake and make the whole effort pointless. Time-Saving: The clamp can save time. You can adjust it up to 24 inches. However, the wood board will not be affected by this procedure. Before jumping into the how-to part, it’s important for you to know the tool you are about to use. So, here’s a little introduction to a straight-edge guide. First off, take a deep breath and let go of any silly notions of cutting a perfect straight line on your first try. Sure, it might look jagged and wobbly if you don’t get it right, but don’t worry, more wood is always available to practice with later!

See, that wasn’t so hard was it? Now you can make perfect straight lines with your circular saw and impress everyone with your sawing skills! Measure Your Cut

Just make sure you don’t forget to turn off the saw because that could be a bit of disaster, man. You don’t want the blade still spinning when you try to take it off the wood. Talk about a mess! Not only that, it could be quite dangerous if you don’t know what you’re doing. Most likely you will end up with a few sawdust related accidents and nobody likes that, do they? That’s about all there is to setting the depth and angle of your circular saw! Just follow these steps next time you’re cutting something, and you’ll be sure to get a perfect cut every time. And remember, always be careful when using power tools like this, as they can be dangerous if used incorrectly. Now let’s go make some awesome saw cuts! Safety Tips If someone suddenly enters and something happens, it will be fatal. And you are working with blades. Any accident will take a huge toll.

You will find most straight edge guides with a swivel head. This swivel head lets the clamps grab at an angle the wood piece creating a straight fence for your circular saw. The fence attaches to the wood piece that doesn’t come with parallel edges.

Highest-Rated 2023 Circular Saw Guide Reviewed in Detail

Aluminum is another promising material for a saw guide, especially if portability is important to you. It’s slightly more prone to flexing or bending over long-term use, but its lighter weight makes up for it. Use it with some extra care, and it won’t bend for years to come! If you want absolutely no compromise on solidity and shape retention, steel would be your best bet. Size First thing’s first: Make sure you’re always using the best and sharpest blade for the job. That’s right, the sharpness of the blade will make a world of difference in the quality and accuracy of your cut. If your saw is equipped with a jagged or dull blade – toss it! If the blade isn’t sharp enough it can cause the edge of your saw to tear the material instead of slicing it as it’s meant to. Place the circular saw, and align the blade of the circular saw with the cutting line to see if the alignment of the edge guide is perfect or not. If it’s not, the cut will not be straight. If the alignment is not the same, follow the process again and mark more carefully using the speed square. Step 6 Straight edge clamps are usually of aluminum. You will find straight edge clamps made of extruded aluminum, rigid enough for holding the straight edge. It can also withstand constant use. The width of this aluminum is up to three inches to resist bowing. Anyway, to adjust your saw, you need to make sure that the blade is parallel to the cut that you’re making. To do this, you’ll want to tilt the blade downward and cover the blade with the handle of your tape measure. Then use a straight edge along with the handle of the tape measure to ensure that the blade is on the same level as the straight edge.

For those who need to handle larger projects, the Bora NGX 50-inch aluminum extension can be easily added to increase the guide's length up to 100 inches. This extension is a reliable solution for those who need to cut larger sheets of plywood or other materials.

Ahh, so you’re a whiz at getting your circular saw set up, nothin’ on this good earth could possibly stop ya now– except maybe straight cutting with it. Making a straight cut with a circular saw can be a real challenge, especially if you have less than steady hands. For every plank to have the same straight cut, follow the procedure of aligning the edge guide every time on the cutting board. That way, with every rip cut you make, you will get an equal-sized plank. You can use the two guides separately. They are made of aluminum. The sled and the connectors are consisting of hard blue plastic material.