Joined in 2023 
82 
63 About this deal
Protect your solar panels from pigeons, seagulls, birds nesting and other pests with our reliable and easy-to-install pigeon proofing solar panel wire mesh or weld mesh nylon clips solution. Our solar panel pigeon proofing wire or weld mesh installation clips provide a physical barrier that birds and other pests can’t pass through. These solar panel pigeon proofing wire or weld mesh clips are made from high-quality nylons and are easy to install, so you can protect your solar panels in no time. This non-penetrating system is fast and easy to install and does not void warranties, please see installation images bellow. Our mesh products and associated kits are designed as a control and prevention solution to prevent pest birds such as pigeons from gaining access to the underside of solar panels. Birds are commonly found under solar panels as the design allows for easy nesting access and mimics a safe habitat away from predators and weather; once established, birds are unlikely to move on without eviction. STEP 2: Set the wire mesh screen in place. Make sure the fastener rod comes through the screen at an upward angle as to keep downward pressure on the screen STEP 2: Set the wire mesh screen in place. Make sure the fastener rod comes through the screen at an upward angle as to keep downward pressure on the screen.
A typical solar panel is approximately 1.6m tall and 1m wide, on a typical panel one should use 3 clips on each long edge and 2 clips on each short edge. See the diagram attached to this product listing for more details and an example of a typical installation. Looking for a reliable and easy-to-install solution to protect your solar panels from pigeons, birds and other pests? This non-penetrating kit is a fast and easy solution to prevent pest birds from gaining access to the underside of solar panels without drilling and voiding any existing manufacturer’s warranty.
Cut the roll into 1.6 M sections (or length of the longest side of a panel), it is much easier to work with shorter lengths. Installation is simple and non-penetrating, making it fast and easy to install and remove for servicing. Just follow these four steps: Solar panels are being installed on commercial and residential roofs across the United Kingdom at an ever-increasing rate. These arrays provide perfect harbourage for birds, and homeowners are desperate for a solution that does not involve piercing or damaging the solar panels with mechanical fixings or adhesives, hence avoiding warranty infringements. Solar panels are being installed on commercial and residential roofs across the UK. These arrays provide perfect harbourage for pigeons, homeowners are desperate for a solution that does not involve piercing or damaging the solar panels with mechanical fixings, hence avoiding warranty issues.
Include a 75mm (3inch) overlap of the mesh when installing the next section, joint the mesh with stainless steel corner ties (sku- sscabletie) where the mesh overlaps and on the corner joints. Simply place the solar panel pigeon proofing wire or weld mesh nylon clips every 30-40cm along the solar panel frame and pull tight. Roll out the wire mesh or weld mesh and cut it into manageable lengths, then position the wire mesh or weld mesh in place, ensuring the fastening rod points upwards. Attach the fastening washer and join the next section of wire mesh or weld mesh with cable ties.For this clip to work, the solar panel must have a minimum 20mm return lip on the underside of the frame.
Beyond safeguarding against damage, these clips prevent droppings from impacting panel efficiency. They also work to keep other birds and pests away. Our solar panel pigeon proofing wire or weld mesh nylon installation clips are the perfect solution! STEP 3: Slide the speed washer onto the shaft of the clip assembly until snug. Make adjustments to the screen as necessary. Tighten speed washer to panel edge. STEP 2: Set the wire mesh screen in place. Make sure the fastener rod comes through the screen at an upward angle as to keep downward pressure on the screen, pushing it towards the roof.The solar mesh is a heavy-duty and physical barrier that prevents a wide range of bird activity under solar panels, including roosting and nesting. The mesh size will usually prevent smaller birds than our solar spike range and can be effective for starlings and sparrows. The SolarFix system is designed specifically to keep all birds from getting under solar arrays, protecting the roof, wiring, and equipment from their damage. This non-penetrating system is fast and easy to install, and can be removed for service. Solar panels are being installed on commercial and residential roofs across the UK. These arrays provide perfect harbourage for pigeons, homeowners are desperate for a solution that does not involve piercing or damaging the solar panels with mechanical fixings as this will void the panel warranty. These clips are easy to install and effectively deter pigeons from roosting or nesting on your panels. Crafted from durable, weather-resistant materials, they provide long-lasting protection.
The patent-pending plastic clips are not only UV stable but also gentle on anodised frames of solar panels, ensuring longevity. Installation is easy with the spacing of two clips per 450mm (18 inches) on shorter edges and three on longer ones, meaning the mesh is secure without drilling holes or harming the system. Constructed to accommodate the Solar Panel Mesh (WM132), the clips are almost invisible from ground level. Features & Benefits: Solar Panel Mesh Wire Clip the presence of wildlife and debris can cause structural damage. For instance, rodents can chew through the wiring or debris can accumulate moisture, leading to potential corrosion on the roof. This innovative clip is designed specifically to keep feral pigeons from getting under solar arrays, protecting the roof, wiring, and equipment from damage. This non-penetrating system is fast and easy to install. Both types of weldmesh can either be trimmed down with some suitable tin snips or wire rope cutters. Alternatively, excess wire mesh can be bent inwards to create a dual-layer of protection.Maximize the efficiency of your solar panels with our reliable and effective Bird Control Solar Panel Clips. Invest in protection that lasts and reap the benefits of clean, efficient solar power. Mesh Size: 25 mm X 12.5 mm (1″ X 1/2″) (Please note cheaper kits on the internet are sold with inch x inch mesh which is much weaker) This innovative system is designed specifically to keep all birds from getting under solar arrays, protecting the roof, wiring, and equipment from damage.
Great Deal 
New Comment