Fireangel CO-9X Carbon Monoxide Alarm

Product Information

If your CO alarm is flashing a red LED light every 20 seconds, it has been activated recently. This is referred to as ‘alarm memory’, find out more about what this feature means here. Why does my FireAngel CO alarm not sound when I press the test button? An audible Carbon Monoxide detector is the only way to be alerted to a carbon monoxide leak; it can’t be smelt, tasted or seen so it’s impossible for human senses to detect.

https://www.fireangel.co.uk/wp-content/uploads/2022/10/MA0394R1-FireAngel-CO-Icon-Guide-Blog-Assets-Identifier-Guide-Draft-1_Power-Nightime-Sensing.mp4 If your FireAngel CO alarm is fully activating, and you can hear 4 loud beeps, immediately open any doors or windows in your home, stop using any appliances, switch them off and evacuate the building taking the CO alarm with you. Once your CO alarm is activated and tested, choose to install the alarm by mounting on a wall or free standing on a shelf. Your alarm should be placed 1-3 metres away from any fuel burning appliance in your home, in living rooms or bedrooms. FireAngel’s new range of carbon monoxide alarms use intelligent sensing technology for a rapid reaction to rising levels of CO. Find out more about the FA3820X4 CO Alarm. FA3313X4: Carbon Monoxide Alarm with replaceable batteries

With low level CO monitoring, a pre-alarm warning to open windows helps reduce the risk of CO poisoning and prevents build-up of dangerous CO levels. If a room is not ventilated and ppm levels continue to increase, the alarm will activate.

In living spaces: they should be positioned close to where the occupant's head is likely to be most of the time – e.g., on your bedside table. The alarm features the latest CO sensing technology and can be used to replace end-of-life FireAngel CO-9X alarms. Fitted with a sealed, tamper proof battery that will last the lifetime of the alarm. The sensors within the unit will deteriorate after 10 years, so to ensure you’re protected we recommend you replace the unit after this time. Known as the ‘ Silent Killer’, CO occurs when fuels burn incompletely, with common sources being boilers, gas fires and hobs and solid fuel burners. However, carbon monoxide can also pass through walls, so you would also be at risk if a neighbouring property had a leak. CO detectors should be installed near potential sources of carbon monoxide, essentially any fuel-burning appliances such as boilers, cookers and ovens, fireplaces (both open and enclosed burners), and portable generators. As you are likely to be most affected by CO in areas of your home that you spend the most time in it is advisable to install alarms in those areas as well, such as the living room and bedrooms. It is also worth noting that while one detector is better than no detectors at all, larger homes may require several detectors to cover the property fully. Looking for a CO-9D alarm replacement? FireAngel’s new FA3322X4 alarm will be replacing any end-of-life CO-9D alarms.

All alarms are calibrated and rigorously tested in-house and are third party tested to receive the BSI Kitemark certification to provide peace of mind. Also, the new range is compliant with the revised European Standard EN 50291-1:2018 to ensure maximum protection. FA3322X4: Carbon Monoxide Alarm with digital display and 10 year battery Find out more about what you should expect from your landlord for CO safety in your home. Get protected today If your FireAngel carbon monoxide alarm is new and the test button is not working, try removing the isolation pin. Once removed, wait for at least 1 minute for alarm to initiate. If the alarm now sounds once test button is pressed your alarm is working correctly. If it still does not sound, please get in touch with our Customer Support team.

To activate your CO alarm, pull the disabling tab out of the alarm and wait up to 1 minute for the green LED to flash to confirm the alarm is active. After 1 minute, press the test button to hear the alarm sound. Please note, the alarm will not sound before the 1 minute activation period is complete. CO alarms and rental properties If your CO alarm stopped beeping after being outside in the fresh air for 10 minutes, you may have a possible carbon monoxide leak in your home. We recommend calling your gas supplier or national emergency gas helpline on 0800 111 999 and await further instruction. However, if your CO alarm is beeping, flashing red or not responding during a test, follow our troubleshooting guide to decipher the cause. This guide applies to FireAngel FA3313 and FA3820 alarms. Why is my FireAngel CO alarm going off? Under the extended Smoke and Carbon Monoxide Alarm (England) Regulations 2015, from October 1st 2022, a carbon monoxide alarm will be required in all rooms where there is a fixed combustion appliance – such as gas boilers or gas fires – once the compliance date is announced. However, gas cookers are excluded from the updated regulation. Battery powered carbon monoxide alarms can typically be installed wall-mounted or left free-standing on flat, level surface.Experience both audible and visual safety warnings with the digital screen, which will change colour to indicate different incident types for clear safety advice. The FA3820X4 Carbon Monoxide Alarm offers a variety of safety features, including Ventilate Instruction, Alarm Memory, Sleep Easy and Quiet Self Test. With our sleep easy function, you can silence low battery chirps for 8 hours, up to 10 times. This feature not only allows you to enjoy a silent night’s sleep, but gives you vital time to take action and replace your batteries. Once your CO alarm is activated, this icon or ‘heartbeat’ will continue to flash a green LED in power mode. If a battery fault or warning has been silenced for a period of 8 hours and times out during night time, the silence period will automatically be extended once for a further 8 hours (night silence will increase the counter by 1 for sleep easy). Please note, this feature is not available with the FA3820 or FA3313 alarms. Understanding FA3322 digital display indicators

Our FA3322X4 Carbon Monoxide Alarm with digital display comes with a sealed, tamper proof battery that will last the lifetime of the alarm. The sensors within the unit will deteriorate after 10 years, so to ensure you’re protected we recommend you replace the unit after this time. FireAngel’s FA3322 digital carbon monoxide alarm features many icons on the LCD screen. View our guide below to help you understand what each represents.

Key Product Features

With a multi-functional LCD digital display and array of exclusive features such as Alarm Memory, Ventilate Instruction, Quiet Self Test and Environmental Sensing, the FA3322X4 offers the highest level of CO detection for your home. If you have had your FireAngel carbon monoxide alarm for a few years but it is still within warranty, and the isolation pin has been removed, please get in touch with our Customer Support team. If it is not within warranty, please replace your alarm as soon as possible. Why is my FireAngel CO alarm beeping? The advice below is purely provided for ‘best practice’ and should not be used independently. Please note, these alarms are not suitable for homes in Scotland under the new Fire & CO regulations. Tenants, do you know your rights as a renter when it comes to CO alarms in your home? The Government announced its response to a consultation on the use of smoke and carbon monoxide alarms in domestic properties. CE marked and Kitemarked to BS EN 50291-1 (domestic use) & BS EN 50291-2:2010 (camping/caravans/boats)