There's really no point in buying "satin" if you are going to wipe it on. If you thin gloss material and wipe it on, it's going to dry satin anyway. "Canned satin" will work, so go ahead and use it, but the problem with canned satin polys and varnishes is that they are made by adding fine "dust" to dull the gloss and you must regularly stir the stuff in the can to keep the "dust" in even suspension in the material. (Varnishes are always stirred, never shaken. Shaking ads minute bubbles to it which will ruin the finish.) Those who don't know this will often apply "satin" finishes right out of the material at top of a can in which the "satin dust" has settled and then can't figure out why their finish turned out glossy. Take Tow and lay it out on some plastic sheet, taping the ends down so they do not move and the tow is as flat as possible. (you might roll it a bit). then spray 3M77 on the one side of the tow. Use a bit of 3m&& since you want the adhesive there. Then let it cure/dry. Taking the tow and a small monokote iron, position the tow with the adhesive side on the foam and iron on the tow. Trim as necessary. Then do your layup. I have don't this with pre-cured CF pieces and the 3M77 melts and adheres to the foam exceptionally well. Well enough to rip out the foam if you decide to try to remove the CF. The Guild is a non-profit educational organization whose mission is to “Advance Ship Modeling Through Research”. We provide support to our members in their efforts to raise the quality of their model ships. Keep in mind that oil-based sealer will make your wood appear darker and warmer, which may or may not be a good thing. If you are sealing over light wood or something you want to look very rustic, polycrylic may still be a better choice.

Can polycrylic be used on all types of surfaces? Polycrylic is generally safe to use on a wide range of surfaces, including wood, painted surfaces, and even paper or fabric-based projects. However, it is important to test a small, inconspicuous area first to ensure it adheres properly and does not cause any damage. How long does polycrylic take to dry? The drying time for polycrylic can vary depending on factors such as humidity, temperature, and the number of coats applied. Generally, it takes about 2-4 hours for polycrylic to dry to the touch, and 24 hours for it to fully cure. Polycrylic is a water-based, clear protective finish that can be applied to a variety of surfaces, including wood, metal, plastic, and more. This type of finish is known for its durability, clarity, and ease of use, making it an excellent choice for many different applications. The Validol, as well as others perhaps, lines the TE of the stab and rudder with 1/8" (or so) wide CF uni tow. The Tow provides better resistance to damage. CF matt basically absorbs a lot of resin and might not give you the desired strength.Semi-gloss: A higher-gloss finish that provides a noticeable level of shine, without being too reflective or mirror-like. Let the first coat dry: Allow the first coat to dry completely, following the manufacturer’s recommended drying time.

Ahoy, Tony ! I used to like the 'Minwax of Old' for general woodworking, but it has been significantly re-formulated to comply with VOC reduction ... likely a good thing. Now, as then, it really takes 3 or 4 days to dry - and in the interim it gives off a distinctive odor - a litttle less each day. Its still good as a colorant, as I had to match some unfinished red oak stair 'bull-nose' to pre-finished 3/4" tongue and groove red oak flooring. I started with Minwax that was a little lighter (and a slightly different chroma) than the flooring, then added small amounts of artists' oil colors (thinned with a little Minwax clear). Just a little at a time to the container used for mixing enough for the need, as it is hard to 'lighten' if one goes to far. A test piece of oak was used and compared to the finished flooring (which had some color variations inherent due to variations in grade. Also I was using #2 common, less expensive than pricy #1 - yet still much better than the next lower grade.). If you enjoy building ship models that are historically accurate as well as beautiful, then The Nautical Research Guild (NRG) is just right for you.Seems that Minwax is fully compatible with artist oils, and to be sure of my color (after 'force drying' the test piece with a blow dryer) a little clear varnish was applied over to get the sheen of the pre-finished flooring - and the color would be 'flat' without the top coat of varnish. It looked good, so I went ahead and treated all the bull-nose needed. One day later I applied the clear Varnish (Varathane clear - a different brand name, but also compatible with Minwax) and the next day was able to go ahead doing the landing into our sunken family room ... We can't tell that anything was matched, it looks that good.